Voest lathe manual. Used X VOEST GAP BED ENGINE LATHE for sale 2019-03-23

Voest lathe manual Rating: 6,9/10 496 reviews

VOEST DA160 Lathe (a re

voest lathe manual

By using a system normally only found on better classes of toolroom lathe, with a speed-change gearbox in the cabinet stand and the drive to the headstock spindle by belts, the makers had taken unusual care, for a general-purpose lathe, to minimise headstock vibrations and gear-tooth chatter marks on workpieces. An all-lever and dial-change, oil-bath screwcutting and feeds gearbox was fitted - with no open slots to allow in swarf and dirt. A very similar larger version was also produced. Unimat was sold some years ago. Some of the other brands were Unimat, Maximat and Emco Maier.

Next

Used Lathes up to 20 feet long

voest lathe manual

At Rohner Machinery, we pride ourselves in giving the customer top quality new and pre-owned machines for every application. A larger version of this lathe was also made which, although it looked very similar, was of 10 to 11-inch centre height and around 60 inches between centres. As an added bonus, the handwheel was provided with a micrometer dial. To ensure the quality of our equipment, all of our machines go through a thorough inspection process. If you have a Vöest lathe, would be interested to hear from you. The drive to the 46 mm 1. Hope it work for you.

Next

Voest Apollo 520 x Geared Head Gap Bed Engine Lathe

voest lathe manual

The shear-pin protected 4 t. If you want to know more or withdraw your consent to all or some of the cookies, please refer to the. The two longer-bed machines had gaps with the capacity enlarged to 570 mm 22. Basically a single phase induction motor has a run winding and a start winding and to reverse the direction the connections to one winding, usually the start winding, must be reversed and that is the function of the lathe switch. The 13-inch wide bed was very deep, with massive diagonal ribbing, and the 1000 and 1500 mm between centres models could be supplied, at extra cost, with induction hardened ways to a minimum specification of 300 Brinell.

Next

Voest Apollo 520 x Geared Head Gap Bed Engine Lathe

voest lathe manual

Speed-change gearbox and flange-mounted motor The drive to the 46 mm 1. Voest Alpine is now owned by Weiler in Germany. Finally, all of our machines are guaranteed with a return policy to ensure the customer will be satisfied. Vertical milling attachment fastened to an angle plate bolted in place of the top slide. Earlier Vöest with typical 1950s rounded styling.

Next

Info on Voest Lathe?

voest lathe manual

Early and late versions of the model were made, those from the 1950s and 1960s being of typical rounded appearance and the later types with much more modern, angular styling. A plunger pump supplied lubricant to the headstock gearing, with a separate piped supply fed directly into the spindle bearings; a flow-checking glass ensured the operator that all was well with the system - at low speeds the pump dripped its supply against the window, whilst at higher revolutions this should have changed to a spray. The carriage traverse handwheel was fitted with a micrometer collar, but could not be disengaged from the rack. Back in the sixties, the Austrian schilling was at 13 to the U. Single phase motors are easily damaged and so if any doubt exists I strongly suggest you ask a motor specialist for assisstance. By closing this banner, scrolling this page, clicking a link or continuing to browse otherwise, you agree to the use of cookies. .

Next

VOEST DA210 CONVENTIONAL LATHE UNDER POWER & FOR SALE @ ROHNER MACHINERY

voest lathe manual

The headstock incorporated an 8 : 1 backgear assembly, with hardened gears that, together with the base-mounted gearbox, gave a range of 12 speeds from 21 to 1500 rpm. Motor terminal box sometimes has a connection diagram inside the lid. Two fabricated steel plinths were used, joined by a full-length slide-out chip tray, but unfortunately without any storage provision. By changing one gear it was possible to cut a range of Diametral and Module threads; the makers also gave instructions for simple rearrangements of the changewheels that produced a very fine feed rate one-half of those normally used and a coarse rate of twice the normal feed - though in the latter case they cautioned that only the slowest spindle speeds should be used. Fitted with a standard-fit 4-way toolpost, the top slide was clamped down by four bolts to a full-length cross slide that, unusually on this size of lathe, incorporated two T slots in its rear surface for the mounting of a cut-off or other type of toolholder.

Next

Used Lathes up to 20 feet long

voest lathe manual

The box was of the dual kind, able to generate, without changing any of the drive gears, a total of 66 English pitches from 1 to 56 t. Practical Machinist is the easiest way to learn new techniques, get answers quickly and discuss common challenges with your peers. The oil-immersed 6-speed gearbox was driven by a flange-mounted 4 h. Call us toll free 888-440-4460 Visit us Or go directly to our Ebay store where all our inventory is listed Sincerely, Rohner Machinery Sales, Inc. We are also a full service rebuilding and repair shop and can handle most any rebuild or repair job. Voest Alpine continues in the steel processing area, but I guess Asian lathe pricing has made lathe mfg difficult.

Next

Info on Voest Lathe?

voest lathe manual

It was designed so that, when worn, it could be easily removed and reversed and the seldom-used section at the tailstock end brought into play. April -10-2008 these publications are dated 1959 and are for two styles of lathe, variable speed or gear drive. With a spindle diameter of 58 or 65 mm the tailstock used either a No. Three between-centres capacities were available of 1000, 1500 and 2000 mm with the shortest bed model offered with the option of a detachable gap able to accommodate a piece of material 440 mm 17. Double-walled, with a held a supply of oil within its base from where it was distributed by splash to the various gears and shafts, the apron used power sliding and surfacing feeds driven by a separate shaft protected by a shear pin. The 66 rates of power feed ranged from 0. They were constructed to Din 8606 standards and designed to compete with established models, such as the Colchester Mascot, at the heavier end of the general-purpose workshop lathe market.

Next