Turn off the water to end flushing. After selecting new bearings, recheck the oil clearance with plastigauge. Never touch any electrical parts. Install new gaskets, O-rings, cotter pins, and lock plates when reassembling. Wear protective clothing, insulated gloves and eye protection. The balancer gear service is included in section 10. Four-valve cylinder-head design with a narrow 30-degree included valve angle creates a compact combustion chamber for optimum efficiency and power output at all rpm levels.
Flush for approximately 5 minutes. Remove the safety lanyard and disconnect the negative battery cable to prevent accidental engine starting. However, if the low oil pressure switch detects an engine oil pressure below 20 kPa 0. The motor could suddenly start, causing serious injury. Engine-cooling water also circulates through the turbocharger housing to ensure optimum compressor function. Apply the polish or wax to the hull and deck according to the instructions on the container. Select replacement bearings from the code tables.
Proper storage consists of checking the entire watercraft for damage or broken parts; lubricating parts to ensure that they do not become rusted; and, in general, preparing the watercraft so that when the time comes to use it again, it will be in top condition. Use only metric tools when servicing the watercraft. The scavenge pump transfers oil from the sump to the oil tank. Check those connections before proceeding. After reassembly, check all parts for proper installation and operation.
Route all electrical wires as shown in the Cable and Harness Routing page 1-31 or 1-52. The tank shape and location, together with a specially designed internal multi-baffle system, optimize engine lubrication under the wide variety of marine operating conditions. If you do not follow this procedure, water will flow into the exhaust and possibly enter the cylinder head and engine, resulting in damage, contamination, or hard starting. Lubricate any sliding surfaces before reassembly. With step-by-step instructions, clear pictures, fluid capacities and specifications, you will have the information you need to get the most from your vehicle. Written for you by Honda, this factory-published original manual shows you how to operate your vehicle.
These products will damage the gel-coat finish. Use only a non-abrasive polish or wax made specifically for marine watercraft. When tightening bolts or nuts, begin with the larger diameter or inner bolt first. Wipe off excess sealant thoroughly. The feed pump draws oil from the oil tank and supplies it to various engine components. This dry sump design incorporates an oil cooler that lowers the oil temperature.
Manuals and user guides for honda aquatrax r 12x we have 3 honda aquatrax r 12x manuals available for free pdf download owners manual honda aquatrax r 12x owners manual 252 pages. If the high oil pressure switch detects an engine oil pressure below 216 kPa 2. Do not disassemble in a way other than shown in this manual. The camshafts can be serviced with the engine installed in the hull. Engineered to withstand the rigors of marine duty. The top piston ring land is anodized, and a chrome-plated top ring further enhances durability.
The turbine bearing is an enclosed, ceramic-ball design that withstands sustained high-rpm compressor operation while providing nearly vibration- and friction-free performance. A two-way valve controls internal tank pressure and prevents water intrusion or fuel leakage if the hull is accidentally overturned. Replace them with new ones upon reassembly. Buy now to own the best manual for your vehicle. A sophisticated throttle sensor and advanced fuel-injection mapping combine to produce smooth and linear throttle response, responding precisely to minor throttle and wastegate changes to maximize driveability, acceleration and drive-pump performance. Metric bolts, nuts and screws are not interchangeable with English fasteners. Never attempt to perform any work with out the assistance of a service manual.
Persons without such knowledge and skills should attempt with caution to service any component or engine by relying on this manual only. Turn on the water to begin flushing. General knowledge information is not included. This engine can be positioned lower than conventional engines, because the oil is not stored in the lower portion of the crankcase. Never run the engine in an enclosed area.
Aquatrax f 15x hondas aquatrax f 15x is the perfect choice for on the water fun why this three passenger beauty is packed with the features and engineering youd expect from a honda featuring a 1470cc fuel injected and turbocharged four stroke powerplant the f 15x rocks on the waves the hull is an ultra stable design. Owner's manuals are also called owner's guides, operating manuals, reference books, or glove box manuals. A damaged throttle body may cause incorrect throttle and idle valve synchronization. Clean parts in cleaning solvent upon disassembly. The AquaTrax turbocharger produces a maximum boost of 10 psi to generate more power than a normally aspirated engine. Connect a garden hose to the flush connector fitting. Read and refer to the other sections in this manual for information regarding proper inspection and service procedures.
Keep flammable materials away from the electric heating element. Improper repair may result in injury to the mechanic and may render the engine unsafe for the watercraft operator and passengers. Parts that do not meet Honda's design specifications may cause damage to the watercraft. Also, there is a flashing indicator light and audible alarm for fuel level, battery charge, coolant temperature, oil pressure and fuel injection. Description : Honda aquatrax f 15x with gpscape f 15x f 15 manuals manuals and user guides for honda aquatrax f 15x with gpscape f 15x f 15 we have 1 honda aquatrax f 15x with gpscape f 15x f 15 manual available for free pdf download owners manual.