Hp laserjet 5p user manual. HP LaserJet 5P manual 2019-02-15

Hp laserjet 5p user manual Rating: 9,8/10 1306 reviews

Support for C3150A HP LaserJet 5P Printer

hp laserjet 5p user manual

Make sure the paper is flat in the tray at all four corners. The printer will automatically begin printing. A secondary light pattern will indicate the specific error: Error light on ­ Memory overflow. Make sure the paper is flat in the tray at all four corners. Print a test page and when half way through the printer open the lid and verify if the marks are appearing before the fuser which would point towards the toner. Error, Data and Ready lights on ­ Temporary Error. Since the regular tray works and I have other printers I can use for manual feed it hasn't been a big priority - but you are motivating me to get going on it.

Next

Solved: hp laserjet 5 printer driver for windows 10

hp laserjet 5p user manual

Grasp Tray 1 by the two finger tabs and pull the top down. Align the pointer on the end of the guide with the desired paper size. Ready and Tray 1 lights on ­ Continuable Error. This could cause a paper jam. Changing Paper Size in Tray 2 1.

Next

HP LAserJet 5P

hp laserjet 5p user manual

Press Go to clear the message. Manual Feed and Manual Feed with Pause are available in most software applications under the Print or Printer Setup options. If it does not print, I would lean towards a bad or flakey engine control board. Before I plugged it in I cleaned out the dust with compressed air. A temporary error occurred during printing.

Next

Hp Laserjet 6P User Manual Pdf

hp laserjet 5p user manual

Tray 2 empty light on ­ Tray 2 is empty. Check the toner cartridge, being careful to position it correctly. Manual Feed Printing The manual feed feature allows you to feed paper from Tray 1 rather than automatically feeding from Tray 2. Inserting paper longedge first may cause a paper jam. If the roller turns, then the engine board should be ok.

Next

HP LaserJet 5P manual

hp laserjet 5p user manual

An abnormal break during transmission of the data from the computer to the printer. The lights can either be on, off or blinking. Tray 1 light on ­ Temporary Connection Break. It usually breaks right where it connects to a terminal. The difference was that the crack had not completely severed down to the shaft yet so the part does work. A secondary light pattern will indicate the specific error: Error light on ­ Memory overflow.

Next

HP LaserJet 5P manual

hp laserjet 5p user manual

My Windows 10 Professional 64-bit system has two built-in drivers for LaserJet 5 printers : You may have to click the Windows Update button in the Add Printerdialogue, then wait perhaps for several minutes whilst additional drivers are downloaded, before the list is repopulated. An abnormal break during transmission of the data from the computer to the printer. The printer detected a problem requiring service. Slide Tray 2 completely back into the printer. Add paper to Tray 2. I've been after the webmaster for 2 months to post a series of engine test photos, 5P being one of them. Pull out the tray extender until it snaps into place.

Next

HP LaserJet 5P manual

hp laserjet 5p user manual

Reset the printer by briefly turning the printer off and back on. Load up to 250 sheets of paper in the tray. Slide Tray 2 completely back into the printer. Tray 1 light on ­ Temporary Connection Break. Slide the paper width guide to the left until it lightly touches the media without bending it. If a coil is open circuit and not burnt out sometimes you can resolder the coil wire. Changing Paper Size in Tray 2 1.

Next

Solved: hp laserjet 5 printer driver for windows 10

hp laserjet 5p user manual

Manual Feed If the Manual Feed option is turned on, the printer will automatically print on the media located in Tray 1. Check the cable connections to see if they are secure. Error Messages Error light is on, all other lights off ­ Recoverable error: l The top cover is open. Make sure the paper is flat in the tray at all four corners. It may be the solenoid. The lights can either be on, off or blinking. Move the subtray to the rear position C , aligning the tabs on the front sides of the subtray with the rear grooves.

Next