Injection type Fuel pressure bars Overspeed cut-off rpm 5500 5800 Injector resistive value ohms 14. Complete coverage for your vehicle Written from hands-on experience gained from the complete strip-down and rebuild of a Citroen C2, Haynes can help you understand, care for and repair your Citroen C2. Do not alter the position of the nut d malfunction. Do not expose the cartridge, the filter and seals to pollutants. Front brake caliper, Bleed screw 5. Do not separate the following components from the diesel injector carrier 3 : - Diesel injector e no replacement parts. «b» Location for engraving of serial and gearbox nos.
In order to strengthen its position in the Chinese market, in 2006 Citroen C2 began to sell the converted Peugeot 206 under the name Citroen C2. We have 47 used manual citroen c2 for sale from rac cars local approved dealers click here. All interventions on the injection system must be carried out to conform with the following requirements and regulations : - Competent health authorities. B: Pegging on the automatic gearbox. The gear selection control and gear engagement control cables cannot be adjusted. If it is not correct, repeat the operation to tension the timing belt see corresponding operation.
Remove: - The engine support 8. All its essential components and connections are illustrated by graphic symbols arranged to describe operations as clearly as is possible but without regard to the physical form of the several items, components or connections. Raise and support the vehicle on a two-column lift. All interventions on the injection system must be carried out to conform with the following requirements and regulations: - Competent health authorities. Remove: - The three screws 1. Centre the hydraulic block, using screws 11 and 12.
Disconnect the connectors of the following components: - The cigar lighter 2. New components: - Suspension arm ball-joint. Dissymmetry of lower camb8er 0° 18. Place the sun roof switch in the maximum tilt position. Concerns vehicles equipped with aircon without temperature regulation. Remove Slacken: - Screws 6 , 4 and 5.
A 5 Pressostat : 1,8 ± 0,6 m. Peg the flywheel at «b». Retrieve the brake fluid reservoir from its supply pipes by pulling upwards. Hold the tensioner roller, using a hexagonal spanner at «b». Remove the new cartridge from its packaging. Before working on the injection system, it may be necessary to clean the apertures of the following sensitive components: refer to corresponding procedures - Fuel filter.
Raise and support the vehicle, front wheels hanging. Visit us today for affordable used cars in Northumberland. Checking the compressor oil level. Proceed in the opposite order to removal. Rotate the crankshaft to bring the camshaft towards its pegging point. Do not separate the pressure regulator «c» from the injection common rail 2 Risk of malfunction. Refit: - The timing belt protector 13.
Refit the oil level plug 3. Engine type Engine with filter element 4,25 3,75 1,55 3 Bandween min. A : Rear brake caliper B : Rear brake drum Bleed screw 6. Disconnect the connectors of the following components: - The cigar lighter 2. To release sleeve stops: - Press on the tabs of the clip 6 at «a». Refit: - The lower, intermediate and upper covers 5.
Associated with the manual gearbox, this system suggests when to change up to obtain optimum fuel consumption. Hatchback versions offered for the year 2018 with complete specs, performance and technical data in the catalogue of cars. Temperate : Starting possible as low as -18°C. This is a must buy for any Citroen owner or anyone working on Citroen vehicles. Preliminary operation: - Disconnect the battery negative terminal. Remove: - The air filter assembly 3.
Turn the tensioner roller 7 with the aid of a hexagonal spanner at «a». Raise and support the vehicle, front wheels hanging. Allow the clutch pedal to come back up to its high position. Cold : Starting possible as low as -25°C. Fit the timing belt on the crankshaft pinion.